Skip to main content

Replacement Remotes
Code Alarm-Prestige-Pursuit-Ford Replacement Remote Search
Vehicle Specific Ready Remote Starter Kits
Plug and Play Remote Starters
Plug&Play Remote Range Extender Upgrades
Flashlogic Bypass Interface Kits
1Z-VSS Vehicle Specific System
DIY 3Z-VSS Remote Starter Keyless Entry
DIY Prestige 901TM-VSS Vehicle Specific System
DIY 57TM-VSS Remote Starter Keyless Entry
Pursuit 183BPR-VSS Remote Starter Kit
DIY Prestige 787Z-VSS Vehicle Security Remote Start
Prestige APS997Z 2-Way Remote Starter
Prestige 596Z-VSS 2-Way LCD Alarm with Keyless Entry
Smartphone Control Voxx CarLink ASCL6
Motorcycle Alarm
FlashLogic iDatalink DEI Firmware Programming
Plug and Play Remote Starter Kits
Code Alarm Remote Replacement Case Kits
Remote Car Starter Auto Alarm Keyless Entry Parts and Accessories
Code Alarm Remotes Technical Support
DIY Remote Starter How to Videos
Installing Programming Code Alarm Frequently Asked Questions
Contact Us 1-866-244-8004
Troubleshooting Remote Starter Installation
OEM Factory Replacement Remote FOB
Remote Starter Alarm Installation Manuals Owners Manual
Returns Refunds Exchange Policy
DIY Remote Car Starters Product Reviews

Order by Phone processed by Stripe
50 50 Payment Plan


MotorCityRemotes Remote Starter Car Alarm Troubleshooting BLOG


Read about common and not-so-common problems experienced with remote starters, car alarms and keyless entry systems.

Having a problem with a remote starter installation? Purchased a vehicle with an existing system and having some problems with it? Need a little direction or advice? Report your situation to us and we will be happy to try to help! With 30 years of installing car alarms and remote starter systems, there's a good chance we have seen the same problem before and can provide some recommendations and/or the fix you're looking for.

Troubleshooting Remote Starter

Wednesday, December 04 2019

How to determine if your vehicle is equipped with an OEM factory installed alarm system:

Step A: Roll down the driver’s door window: OEM alarms are set one of three ways depending on the model of vehicle:

#1 Close all vehicle’s doors and lock the doors using the factory remote or #2 press the power door lock switch in the vehicle while the driver’s door is open then close the door or #3 close the driver’s door and turn the driver’s door key cylinder to the lock position with a key.


Step B: After locking the vehicle's doors using one of the three procedures above, wait at least 1 minute then reach in through the open window and manually open the driver’s door from the inside (some vehicles may require pressing the power unlock switch first). If the vehicle is equipped with a factory alarm system the vehicle’s horn will start pulsing all most immediately after the driver’s door is opened.

Posted by: MCR AT 08:55 am   |  Permalink   |  Email
Tuesday, November 26 2019

How to Activate a Code Alarm and Prestige Remote Starter System:

To activate the remote starter, slowly press and release the CIRCLE ARROW button 2X (or key icon on some versions) within 3 seconds (if you have problems, try pressing the button 3X, if it activates after 3 presses it means your not pressing the button the 2X in the proper amount of time, either to fast or to slow)

When you enter the vehicle, turn the ignition key to the ON position (Do not crank the vehicle), then when you step on the brake pedal to shift into gear, the remote starter will automatically shut OFF but the vehicle will remain running because you turned the ignition on first...

So, if you step on the brake pedal before you turn the ignition on, the remote starter system will shut down and you will have to restart the vehicle with the key.

Posted by: MCR AT 08:30 am   |  Permalink   |  0 Comments  |  Email
Thursday, August 29 2019

Programming Older Code Alarm & Chapman Remotes:

Many calls come in regarding problems with programming older Code Alarm and Chapman system remotes. It seems that either they can get the system into remote programming mode but can't get the system to accept the new remote or can't get the system into remote programming mode at all. Here's a couple of tips that have helped hundreds of customers in the past get their remote programmed:

#1 in the step where it states that after the system responds with 3 pulses/flashes release the programming button and then press the LOCK/ARM button on the remote, instead don't release the programming button after the 3 pulses/flashes are heard and while stile holding the programming button in, press the LOCK/ARM button on the remote and the system will respond with one pulse/flash indicating the remote has been programmed, then release the programming button and turn the ignition off...

#2 for systems that get no response at all, in the step where it states to press & hold the system's programming button in, instead close the vehicles doors and wait until the interior lights turn off then turn the ignition ON and turn the vehicle's dome light switch ON/OFF 3X (ON - OFF - ON - OFF - ON - OFF), if this is your type of system, your power door locks will cycle up and down 3X and/or flash the dash lights 3X indicating that you're in remote programming mode. Then quickly press the LOCK/ARM button on the new remote and the door locks and dash lights should cycle one more time, indicating that the remote was just programmed successfully. Turn ignition off and test remote.

Posted by: D. Weber AT 01:00 pm   |  Permalink   |  0 Comments  |  Email
Sunday, June 02 2019

Buyer Beware Before You Buy!: Not all remote starters offered online are DIY  (Do-It-Yourself) systems or can be taken to your local shop for installation

Almost on a daily basis, we receive calls for help with several different brands and models of remote starters and alarm system's that were bought online whereafter they were received the system didn't provide any information other than the basic wiring of the system, no specific information regarding how it's installed in the vehicle they wanted to install the system in or what additional parts may be required.... and with no technical support to call!

Although we try to help these DIY individuals as best we can within a margin of time, this has motivated me to post some "before-you-buy" information insights. After reading and following this information, you will be much more prepared to purchase any system online without the worry of any buyer's remorse. 

First things firstIf your not the car-savvy DIY type and you see a system on the internet that interests you unless the same company that is offering the system to you will install it for you too, don't buy it! It's that simple.

There are several reasons for this, but I will sum it up for you this way; you don't want to be driving around town walking into automotive accessory shops with the system under your arm trying to find someone to install it. Most won't, and for good reason. And that's another long list of why they won't, starting with that they are either just not familiar with the brand of the system and don't want to cause any headaches for you or them in case of any technical difficulties during installation or after. Rule #1: Always purchase the same system and the installation from the same facility if you're not going to install the system yourself!

Now, you may be the "DIY" type that's more than capable to install a remote car starter into your vehicle, but without the right information this can slow down your installation. Unless you are absolutely sure you know you can get the system in without anything other than a general installation manual for the system, with nothing about the wiring of your vehicle, then go for it!

But, even if are the car-savvy type...wouldn't you like a remote starter system that has all the parts and information that you need to install the system with no headaches?

For example, take our Prestige 901Z-VSS, it's the "Vehicle Specific System" version of Prestige's popular APS-901Z. The Prestige APS901Z is their universal line of remote starters that require additional parts, vehicle wiring information, and programming to be installed. It's the platform designed for the professional installer that is familiar not only with how the systems wired and programmed but also familiar with the wiring of the vehicle it's going to be installed into.

Additionally, you have to consider this; the APS901Z version will have no warranty unless sold and installed by an authorized dealer, or the distributor that the system was originally purchased from, directly offers warranty replacement. Generally, a manufacturer does not supply a warranty directly to the consumer, the manufacturer supplies warranty service to the distributor of the system. So any defective parts are returned to the provider (a.k.a. "seller"), the distributor warranties the part to the customer, and the distributor returns the defective part to the factory for credit or replacement. This is how it's handled here at MotorCityRemotes...

Posted by: D. Weber AT 05:00 pm   |  Permalink   |  0 Comments  |  Email
Friday, May 17 2019

Code Alarm and Chapman Remote Starter and/or Alarm Systems LED Flashing 2X:

A common occurrence caused by accidentally pressing a button on the remote while the ignition is on (or a combination of buttons), causing the system to be placed into "Valet" mode. On many older model Code Alarm and Chapman remote starter systems, specifically, the Code Alarm CA530 and CA630 models also including the Chapman F50/55 & F60/65 models, if the lock button on the remote is pressed while the vehicle's ignition is on the system will be put in valet mode which will cause the dash-mounted LED to begin flashing in a 2 flash/pause/2 flash pattern and at the same time turn off the remote start and/or alarm features of the system. The only function that will remain is remote keyless entry.

Depending on the version of system, the same procedure that puts the system into valet mode is the same procedure to take it out of valet mode to resume the full functionality and features of the system. There will be 1 of 3 ways that will put the system in and out of valet mode: With the ignition ON (don't start the vehicle) press both the LOCK and UNLOCK buttons on the remote at the same time. If this is the correct procedure for your specific system the LED will stop flashing in the 2 flash pattern. If not, try pressing just the lock button with the ignition on and if this doesn't change the status, simply try pressing just the unlock button on the remote. One of these 3 ways should do it.


Posted by: Derek AT 10:00 am   |  Permalink   |  0 Comments  |  Email
Tuesday, May 07 2019

Check Engine Light comes on after Remote Starter Activation:

Technically, a few situations could cause this problem but below is by far the most common causes:

Even if this situation occurs after the system has been installed in the vehicle for a while and previously worked fine or if this is happening during a new install test, it is commonly caused by one of the remote starter's ignition activation output wires; On a new install, it can be that either a 2nd ignition wire in the vehicle needs to be powered up at the same time as the vehicle's 1st (or main/true ignition) wire or if a 2nd ignition wire was connected to during installation, the output timing of the 2nd ignition wire may not be providing the needed output at the same time as the remote starter's 1st ignition wire. We have even found some vehicles that required the 2nd ignition output to be turned off during crank/start (basically the same as an accessory output wire but a required connection to start. Most accessory output connections are not required to get the vehicle to remote start, they are only needed for HVAC activation).

Now on an existing installation that was previously working fine, the output timing would not change, so the first thing to check is the systems ignition outputs, check both for faulty connections to the vehicle's wiring and test the remote starter system's ignition output wires during remote start activation to confirm that the outputs are working properly. Other than this being the cause, we would have to get a little deeper into the situation which will be another post. 

Please leave any comments or questions below.

Posted by: MCR AT 11:26 am   |  Permalink   |  0 Comments  |  Email
Friday, May 03 2019

 Remote Starter in Valet Mode:

Lots of times people have called in saying that their remote starter all the sudden quit working, that it was working just fine yesterday and now all of the sudden all it does is flash the parking lights a number of times when they try to activate the remote starter. The common cause of this is that somehow indirectly the system was put into what is called the "valet" or "service mode" which inhibits the remote starter from being activated from the remote.

Depending on the brand and model of system installed in the vehicle, there are several ways a system can be put into and out of valet mode. In our experience, the same procedure that puts the system into valet mode is exactly the way it is taken out of valet mode. Here is a few of the most common ways we know of: 

Version A: There's a small ON/OFF toggle switch mounted underneath the driver's side dash somewhere that if installed to close to the driver's left foot or above the knees it could be accidentally bumped into when exiting the vehicle and switched into the OFF position. This commonly happens during cleaning of the vehicle when panels are wiped down and the switch is accidentally flipped into the opposite position. Additionally, on some systems, this switch may not function without the ignition being ON, so you would have to turn the ignition ON first before flipping the switch.

Version B: On most newer remote starter systems theres an antenna mounted on the upper inside of the windshield, top center, on the glass behind the rear-view mirror, or may be mounted in the upper left corner. On most of these systems you will find a push-button built into it. Commonly a small black or gray round disc that softly clicks when you press it. Now this button only works with the ignition ON, and on many systems as soon as you turn the ignition ON (don't start the vehicle) theres also a LED light built into the antenna and when the system is in valet mode, the LED on the antenna will turn ON solid almost as soon as you turn the ignition ON indicating that the vehicle is in valet/service mode. To turn off valet mode, with the ignition ON, simply press & hold this button in until the LED turns OFF (takes no more then 15 seconds). Then turn OFF the ignition, remove keys and test remote starter activation (never try to activate the remote starter with a key in the ignition).

Version C: Same in/out valet procedure as described in version B, but the button is not built into the antenna but instead mounted separately by itself under the driver's side dash like the toggle switch described in version A.

Version D: Almost the same in/out valet procedure as described in version B except you don'y have to hold the button in, you just press & release it 1X. And the button is built into the system's flashing LED mounted on the front of the driver's side dashboard, facing you, commonly located to the left of the steering column. Some can be found mounted thru the steering column covers on the steering column. You will know if the valet button is built into the LED when you can easily push the LED in and it immediately springs back out when you release the button.

Posted by: D. Weber AT 12:02 pm   |  Permalink   |  0 Comments  |  Email
Monday, April 22 2019

Remote Start won't Work after Changing Battery in Car:

No matter what brand or model of aftermarket remote starter system you have installed in your vehicle there's a 50/50 chance that any service done to your vehicle that required disconnecting the vehicle's battery in doing so will knock the system out of its pre-programmed state which will inhibit the vehicle from being remote started.

This is a very common occurrence and is usually caused not by the remote starter module itself but by the additional component called a bypass interface kit. A bypass interface kit is used in addition to the remote starter's main control module to interface with the vehicle's factory anti-theft system. The bypass interface turns off the vehicle's factory anti-theft system to allow the remote starter's control module to start the vehicle.

When the system was originally installed, the installer programmed the bypass to the vehicle which during the programming procedure the component captures the vehicle's anti-theft code and store's it into its memory so when the remote starter is activated, the remote starter turns on the bypass interface kit, the bypass interface kit momentarily sends this copy of the anti-theft code to the vehicle's anti-theft circuit and turns it off so the remote starter can crank/start the vehicle. Now when the vehicle's battery is disconnected it's commonplace that this interface will lose this stored code and will need to be reset and reprogrammed to the vehicle.

The main symptom of this problem is when you activate the remote starter, and if you were sitting in the driver's seat during activation, you would see the ignition turn on and the cluster light up but no crank at all (or on some vehicles may crank but not start). Many vehicles may also show a flashing security light on the dash cluster.

When a remote starter is indicating that this may be the problem, the system's bypass interface kit must be located in the vehicle so that the brand and model of interface kit can be read off of the module in order to find out what that specific model's reset/reprogramming procedure is.

Posted by: MCR AT 07:19 pm   |  Permalink   |  0 Comments  |  Email
Saturday, April 20 2019

 How to Reprogram a Flashlogic FLTB1 Bypass Kit to Ford Vehicles:

ANSWER: Must have to keys to the vehicle, cannot use the same key twice (cannot use a cloned key either).

Step 1: Unplug everything away from the Flashlogic module. Press & hold in the small black push button on the Flashlogic module, while still holding the programming button in, plug in just the black 4-pin plug. When the LED on the Flashlogic module begins quickly flashing rerelease the button:

Step 2: Plug in the remaining plugs into the Flashlogic module: The LED will begin slowly flashing green. While the LED is flashing green, press & hold the button in again and after the LED turns on solid green and turns off, release the button:

Step 3: Next, take one of the 2 keys and turn the ignition ON (DO NOT start the vehicle): Watch for the LED on the Flashlogic module to turn from red to green, then turn the ignition off and remove key: Within 5 seconds:

Step 4: Quickly place the 2nd key into the ignition and turn the ignition ON (DO NOT start the vehicle): Watch again for the LED on the Flashlogic module to turn from red to green then turn the ignition off: Within another 5 seconds:

Step 5: Press & release the button on the Flashlogic module: within 5 seconds, activate the remote starter system: when the above procedures were done promptly and correctly, the vehicle will remote start and stay running.

If the vehicle does not remote start, press & release the vehicle's brake pedal and start the vehicle with a key. Allow the vehicle to run for at least 10 seconds then turn the ignition OFF and remove keys. Try again from step one. If multiple attempts to reprogramming the Flashlogic module fails contact technical support.

Posted by: D. Weber AT 02:16 pm   |  Permalink   |  0 Comments  |  Email
Tuesday, April 16 2019

Shopping for a Remote Starter, Keyless Entry or Alarm System for Your Vehicle

Knowing the industry-standard cost (a.k.a. competitive price) of a remote starter, alarm, keyless entry, or smartphone system installation (parts & labor) for your specific vehicle is a good thing to know before venturing out or making phone calls to the shops in your area. Pricing should vary depending on the brand of the system and the year, make, and model of the vehicle (within our company anyway's). For example, a system with the exact same features being installed into let's say a 2014 Ford F-150 w/standard keys should not cost as much as the same system being installed in a 2019 Dodge RAM with push-to-start ignition. To be fair, if labor varies shouldn't price?

Just remember the old adage, "you get what you pay for" because it doesn't apply any stronger too when shopping for automotive aftermarket electronics. That $99.00 remote starter posted in the weekend paper most of the time is just to get you in the door (our company could not install any remote starter system we carry into any vehicle for $99.00!). And that $59.95 DIY system on Ebay isn't going to get you much closer to remote starting your vehicle either. Go luck.

This brings me to the #1 advice we provide to call-ins and emails regarding our DIY remote starter systems; if your not going to install the system yourself, don't buy our system, always, always purchase the parts and installation from the same facility!! Otherwise, you'll probably end up driving around with our system under your arm (or that system you bought off of Ebay or Amazon) endlessly trying to find someone to install it! Not much of the car-savvy DIY'er? Then return that system you bought on the internet and go straight to your local automotive accessories shop and have the shop provide the parts and labor!

Anyway's, if you would like a solid foundation about the parts and the labor involved, know in advance if your getting a fair price before inquiring to any shop or some recommendations pertaining to warranty and the leading brands and models of systems you may want to keep in mind and look into, click HERE for more information.

Posted by: D. Weber AT 01:00 pm   |  Permalink   |  0 Comments  |  Email
Monday, April 15 2019

How to Find the Correct Replacement Remote I Need?

ANSWER: If you have an existing remote (a.k.a. "transmitter" or "FOB") flip the remote over, there should be an FCC ID on the back. Using the FCC ID on the back of the remote and the number of buttons on the front of the remote along with the brand of system, you should easily be able to locate the remote you need online by typing this information into any search engine. For example, "Code Alarm 2-Button Remote FCC ID: GOH-MM6-101890". Now if you don't have a remote to your system you'll have to search using the system's brand name and the model number of the system, for example, "Code Alarm CA-4054".

Now if you don't know the model number (don't have the owner's/operator's manual) someone is going to have to drop the dash panel down that's across from your knee's when your sitting in the driver's seat and locate the system's main control module. Most aftermarket systems will be easily found because it's usually held up with a few nylon zip-ties against some factory wiring (you'll be able to tell that it was not factory installed). Once the module is located the model number is commonly located right on the top of the module.

Posted by: MCR Tech Support AT 08:52 pm   |  Permalink   |  0 Comments  |  Email
Sunday, April 14 2019

Buying a new replacement remote for your remote starter, alarm or keyless entry system that you have on your vehicle can seem like an easy task when all you have to do is Google the FCC ID on the back of your remote, there's plenty of "Joe's" out there ready to provide. But you have to be careful. We literally get call's everyday from people that purchased a replacement remote everywhere from Ebay to Amazon to even... Kmart? (with lot's of reputable and not so reputable website's in between) and they are looking for help with programming their remote or even need to know how it work's, because none of the places they bought the remote from supplied remote programming instructions or even a phone number where they can get some help!...and the ones that did supply a number, all they could do is provide or repeat the programming procedure you just read off the programming instructions! Most have no hands-on experience or knowledge of the system that's installed in your vehicle...

Shopping on Ebay, Amazon or any other online provider for general consumer products like books, movies, music, shoe's, appliances, TV's etc, etc. is great, but there are some things that just shouldn't be bought from anywhere they can be located. And some of those things are most products that require application procedures to work and could require technical support...

And replacement automotive remotes are a #1 prime example. The tips to keep in mind when shopping online for a new replacement remote are "who is offering the replacement?", "are they directly experienced with the product?", "are they directly associated with the factory (authorized dealer) or a 3rd party?" or do they sell everything under the sun?", "is there a tech support number provided I can call if I need help?", "can I call-in to place an order over the phone or ask some questions?".

Following and keeping the above 5 basic tips in mind will definitely point you in the right and confidant direction for shopping online for a replacement remote.

MotorCityRemotes has been providing technical support, replacement remotes, remote starter and vehicle security systems online for over 17 years and has been in the automotive aftermarket electronics industry for over 30 years. If you have any additional questions and/or need help locating the proper remote for your vehicle give us a call at 1-866-244-8004. Even if we don't provide the remote you need we will be more then happy to help you with finding the one you need.

Posted by: D. Weber AT 11:10 am   |  Permalink   |  Email
Friday, April 12 2019

Programming a new remote to a Prestige brand remote starter and/or alarm system is basically a DIY situation. You normally don't have to take the vehicle in to have someone do it for you. As long as you know where the system's valet/programming/override button is, your good to go. Now, on Prestige systems with a remote start feature the programming button is commonly built into the system's antenna that's mounted on the windshield either behind the rear-view mirror or in the upper left corner. On systems without remote start, this button will be mounted under the driver's dash somewhere (it's the installer's preference where exactly he puts it);

Once you locate your system's programming button simply turn ON the vehicle's ignition (do not start the vehicle), and press & release the button 3X: Almost immediately the system will sound indicating that the system is now in remote programming mode: Now just press the lock button on the remote (or the one button on one button remotes) and the system will immediately sound again in response indicating that you successfully programmed the remote. Within 10 seconds, press the same button on any additional remotes. When finished simple turn off the ignition and remove keys and test your remote.

Posted by: MotorCityRemotes AT 12:31 pm   |  Permalink   |  Email
Thursday, April 11 2019

ANSWER: Not the only cause, but a common problem resulting after any service performed to the vehicle that required the battery to be disconnected. Your mechanic is not to blame! Any aftermarket remote starter system can lose its programming due to a low or complete power loss. Unless the system was placed in "Valet Mode" the system is flashing a troubleshooting code through the vehicle's parking lights to indicate the cause of the no-start problem. To pin-point where the problem is you'll need the system's installation/programming manual (or in most system owners/operators manuals it will at least indicate why it's flashing the number of times but not how to fix it). 

On Code Alarm, Prestige and Pursuit systems, if the parking lights are flashing 7X when you try to acivate the remote starter it means that the system lost it's tachometer programming signal and it needs to be reprogrammed (See Tech Tip #5). 4 flashes can mean it's in Valet Mode (no reprogramming required. See owners/operators manual) and 3 flashes can mean a safety input is activated or defective. Parking lights flash troubleshooting codes will vary from brand model to brand model, but you can either try to take care of the problem yourself if so inclined by obtaining the system's installation manual or loacting a service facility in your area. To locate a service facility in your area; for a Code Alarm system call: 1-800-421-3209 and for either a Pursuit or Prestige system call: 1-800-225-6074. For any system's purchased through, and call: 1-866-244-8004.

Posted by: MCR AT 11:10 am   |  Permalink   |  Email
Tuesday, April 09 2019

Question: I either lost my keys with my with my remote on it or they were stolen, can I somehow erase the one I lost and still use the spare one I have?

Answer: Yes! All you need to do is find out how your specific system's remotes program. If the system you have is an aftermarket system (not installed at the factory) you will be able to do this yourself, but you'll need to know at least the brand name of the system that's installed in your vehicle to find out this information. For example, if you have a Code Alarm brand system just Google "Code Alarm replacement remotes" and call the company that provides replacement remotes (or call us) and ask what the procedure is for programming your specific remote. Then, after you have this information, program the one remote you have 4X in a row. This will erase all the remotes that were lost or stolen. If you have 2 remotes, program each remote 2X.

Now if you have factory remotes you may have to go to either a locksmith or Dealership to have this done. It depends. You'll have to find out if your specific year, make & model of vehicle's remotes can be programmed simply with performing a procedure like Aftermarket system's or if it requires programming through the vehicle's OBDII diagnostic connector. Again, for example, just Google "2014 Ford Explorer factory remote programming". There are many locksmiths that have websites that provide this information for free right on their site (or call us!).

Posted by: D. Weber AT 09:07 am   |  Permalink   |  0 Comments  |  Email
Monday, April 08 2019

Reported Problem: Car will not Start. Is it my Car Alarm causing the problem?

Tech Tip: Another very common call we get in is when someone's vehicle won't start either because their remote is defective and they can't disarm/unlock their vehicle remotely or they bought a used car (and don't have a remote) and after having to replace the vehicle's vehicle's battery (or any service that required disconnecting the vehicle's battery) all the sudden they discover the vehicle is equipped with an aftermarket alarm and now it's triggering and/or preventing the vehicle from being started normally with the key after the vehicle's battery is re-connected.

But first, as a side note, many times even when someone has a system that triggers an alarm when the vehicle's battery is connected and the vehicle won't start, as long as the vehicle's starter motor is cranking over or at least "clicking" at the starter motor, it's more than likely not the alarm system causing the problem. Why? Because aftermarket alarm systems with an anti-theft (a. k. a. Kill-Switch) feature completely stops the power from reaching the starter motor. So, it's only possible that it's the system causing the no start issue is when as soon as you turn the ignition on, everything on the dash would light up as normal (including all accessories, chimes etc.) but when you go to crank the vehicle, no power at all would reach the starter motor. If it cranks, it's not the system.

Now, let's say it's the system causing the no crank issue; all aftermarket systems have a way to emergency-override the system. The procedure commonly involves a push-button or with some systems a small ON/OFF toggle switch. Most manufacturers describe these switches as either an e-override button, valet or programming switch/button. Depending on the brand and model of system these switches are commonly installed by the installer in several different places in the vehicle:

They can be found mounted under the driver's dash either through an existing hole on a factory dash bracket, on a right-angle bracket the installer provided or they drilled a small 1/4" hole in the driver's side left kick panel (this is the panel that curves up to the left from the driver's side door sill-plate to the left of your left ankle when your sitting in the driver's seat. On most vehicles, the panel to the left of the emergency brake lever). I have even found a lot mounted on the bottom of the steering column. And finally, most systems with a remote starter feature, this button is found built into the system's antenna found mounted in the top center of the windshield behind the rear-view mirror or in the upper left corner.

OK! Now that you found what you think is the override button, what now? Well, that too depends on the brand and model of system, but here are the most common procedure possibilities that could emergency override your system:

Enter the vehicle (while the alarm is going off) and turn the ignition ON with the key. Either press and release the button (or flip the toggle switch in the opposite direction) OR press & release the button 3X. If it works, the alarm will shut off almost immediately. Now, quickly try to start the vehicle. If it starts your done, if not, turn the ignition back off, go back to the push-button and press & hold it in and while still holding it in, try to start the vehicle. If it still won't work (maybe the system is defective), the next thing I would do is permanently bypass the system's anti-theft circuit, but that procedure is for another post!

Hope this helped! If it did, please leave a comment, if it didn't, send us your questions!

Posted by: D. Weber AT 01:07 pm   |  Permalink   |  0 Comments  |  Email
Friday, April 05 2019

Reported Problem: Do I Have to Reprogram my Remote FOB after Replacing the Battery in it?

Answer: We get this call almost every day. A properly working remote will not lose it's programming from just changing the battery in it. The number one indication that your remote just needed a fresh battery is when you had to get closer and closer to the vehicle to unlock the doors or activate any other features controlled by the remote. 

But if your remote suddenly stopped working or worked intermittently from any distance and then stopped working, odds are you have a worn-out or damaged remote and need a new replacement. With the exception of some "cloning" type remotes, no factory installed or aftermarket remotes lose their programming.

They are designed with what is sometimes called a non-volatile memory which retains the remote's operating frequency and does not require it's memory data to be periodically refreshed or reprogrammed due to low or complete power loss.

Posted by: NCR AT 09:12 am   |  Permalink   |  0 Comments  |  Email
Tuesday, April 02 2019

Answer: Several calls to our tech support line are questions regarding the location of their remote starter system's remote programming button. Most systems with a remote starter feature have an antenna mounted on the inside of the windshield. This antenna is commonly mounted in the top dead center of the windshield behind the rear-view mirror or in the upper left corner. And the remote programming button is built into this antenna.

When this is the case, you will see a small round button on the top surface of the antenna. On many older systems, this button is found mounted under the driver's dash area or on some system's the button is built into the dash-mounted LED. On many system's with separate buttons (not built-in) the button has also been found mounted on the bottom of the steering column or in the left kick-panel.

Posted by: MCR AT 02:32 pm   |  Permalink   |  0 Comments  |  Email
Sunday, March 31 2019

Reported Problem: Remote Starter Cranks Car but won't Remote Start when Cold

This problem is regularly reported on a weekly basis soon as the mid-west and east coast receives it's first frost towards the beginning of the winter. 

Most Common Cause: The remote starter system may have been installed using a "tachless" mode; This setting can range from voltage level detection or a pre-set crank/start output setting. This is where the system is programmed to either monitor the standing voltage of the vehicle and then compares that voltage reading to the voltage level after it cranks/starts and the alternator kicks in or the system is pre-set to crank/start at a predetermined time, respectively. So, when the vehicle is cold (usually at or below 32°F or 0°C) the system either doesn't detect a significant raise in voltage levels (usually >0.5V) or the pre-set output isn't long enough to get the vehicle to start. While these two settings work fine in warmer environments that rarely see frost (or none at all), it's possible these settings won't provide a dependable start in or during a colder climate.

Possible Fix: Connect and program the system's tachometer input. All remote starters have what is called a tachometer detection input wire. This is a hard-wired connection made directly to either the vehicle's tachometer wire, odd-colored fuel injector wire or a specific coil wire commonly found at the vehicle coil-pack on the engine. This is by far the best way to install any remote starter system regardless of the climate.

When the system is installed utilizing the system's tachometer input, the system directly monitors and detects the small amount of AC voltage that this wire in the vehicle shows while the vehicle is running. Then after this AC voltage level is programmed into the system, when the remote starter is activated and if this level isn't detected right away, the system will automatically crank the vehicle a little longer until this level is detected or it will shut down and automatically try to re-start the vehicle again (on some systems up to 3 times). This connection is strongly recommended on all Diesel engines and will provide a dependable remote start on any vehicle.

Posted by: MCR AT 10:10 am   |  Permalink   |  0 Comments  |  Email
Friday, March 29 2019

Reported Problem: No Horn Honk when Keyelss Entry is used or when Remote Starter is activated

System Status: New Install on some older models of 2001-2003 Dodge RAM's and Caravans

Possible Fix: On some older model's of RAM & Chrysler/Dodge Mini Vans (not limited to these models) the default horn pulse output time setting (that's commonly between 16ms-18ms) on most brands of remote car starters, keyless entry and alarm systems, does not provide a negative pulse long enough to beep the vehicle's horn properly. The results can cause confusion during system programming changes and during normal operation.

When this is the situation, the system must be programmed for a longer horn output duration between 30ms-40ms. Most current systems have this option setting available in their installation manual and as long as you have this information the change is a step-by-step procedure commonly requiring a working remote to the system, an ignition key to the vehicle, and knowing the location of the system's programming button.

If your installing any of the Prestige E, Z and APSRS or APSSECRS series systems, this is how you would turn up the output (and just a example for other brand systems):

TECH NOTE: Each step needs to be performed within 10 seconds of each step:

1: Turn ignition ON (DO NOT start the vehicle: Press button on antenna 3X: System will sound 1X (or dash lights will flash 1X): Cycle ignition from OFF to ON again: System will sound 2X (or dash lights 2X): Leaving ignition ON:

2: Press and release the button on the system’s antenna slowly 3X: the system will respond by flashing the LED on the antenna in a 3 flash/pause/3 flash pattern. Slowly keep press & releasing the button on the antenna until the LED flashes in a 8 flash/pause/8 flash pattern:

3: While the 8 flash/pause/8 flash pattern is seen: keep press and releasing the lock button on the system’s remote (or just the button on the 1 button remotes) until the system beeps the number of times corresponding to the desired horn pulse output time setting (the second setting is usually adequate): 

Response: 1 Beep = 16ms. (Default setting)   2X = 30ms.   3X = 40ms.   4X = 50ms    5X = 10ms.

3:  After the desired setting change has been made turn the ignition OFF and remove keys: Response: wait, the system will sound: The system has now been set to the desired horn pulse output time setting.

Posted by: MCR AT 07:37 pm   |  Permalink   |  0 Comments  |  Email
Thursday, March 28 2019

Reported Problem: Aftermarket Car Alarm Keeps Going Off!

Probably thee #1 reported problem in the history of car alarms is the complaint of the car alarm going off at all hours of the day and night. This would clearly be the most annoying problem you could have with a car alarm and for your neighbours!

Technically, the problem can be from a small list of causes, but fortunately most of the time, it's only due to a sensor being set to sensitive during installation or it just needs a slight adjustment after being in the vehicle after several years. And commonly the #1 culprit is known as a "shock-sensor" or "impact-sensor". These types of sensors as you can guess, detect specific levels of vibrations caused through the vehicle.

When these sensors are set to sensitive (like when an alarm installer tries to use a shock sensor as a glass break detector, which it's not meant to be used for, there are specific sensors for that) the alarm can false trigger with just the wind blowing against the vehicle, when a loud vehicle or motorcycle drives by it or even if a cat walks across the hood!

Shock/impact sensors are only meant to detect larger vibrations or impacts made to the vehicle. Examples would be vibrations caused by another vehicle backing into the vehicle, jacking-up or towing, or if someone literally took a baseball bat or a brick against the glass. Detection for any lighter vibrations made to the vehicle would require a different type of sensor.

The fix: A system's shock sensor is commonly found mounted under the driver's dash area (a.k.a. foot-well area). Usually they are mounted snugly against some factory wiring using a nylon zip-tie. The sensors can range in size from a 2" by 2" small plastic box to almost the size of a pack of cigarettes. They will also have a small 3 or 4 wire plug plugged into it. And, most of these sensors have color LED's built into them that will light up when you tap your finger on them.

When you think you found the sensor, look on the sides of the sensor and you will find either a small adjustment screw in a small hole or on some older systems a protruding adjustment knob sticking out the side of it (a.k.a. thumb pot adjuster that you can turn just using your fingers. The type found through a hole in the sensor is a small eye-glass phillips screw). No matter which type of adjustment you have they all adjust exactly like a volume knob. Turning it clockwise makes the sensor more sensitive (volume up) and counter-clockwise makes it less sensitive (volumn down).

The best way to begin the adjustment of a shock sensor is to turn the sensor all the way down (counter-clockwise) and then slightly turn it up 1/4 of the way. Now, to test the sensor's sensitivity; roll the driver's side window down, close all the doors and arm the system. Wait a minute, then reach in through the open window and bounce the side of your fist off the steering wheel (not excessively hard). Some sensors that are known as a "2-stage" sensor will just pulse the vehicle's horn or the system's siren. This is known as the "warn-away" response. If the sensor either sounds the warn-away signal or does not sound at all (sensors with single-stage sensing) this will probably be a good setting to leave it at and no further adjustment will be neccassary. Now if the system still false triggers, you'll want to try a lower setting or isolate the sensor from the system completely which is done simply by unplugging the plug from the sensor. 

If the system still triggers after you unplug the sensor you know its not the shock sensor causing the false triggering. But if it only falses with the sensor plugged in and after several attempts of making adjustments, you have a bad sensor that needs replacing.

Posted by: MCR AT 11:00 am   |  Permalink   |  0 Comments  |  Email
Wednesday, March 27 2019

Reported Problem: Aftermarket Kill-Switch. No Power Reaches Starter Motor when trying to Crank/Start (all other functions on the vehicle work fine):

We get this call periodically, especially when after someone has purchased a used vehicle with no knowledge of an alarm system even being on it and no remotes came with the vehicle:

Commonly known to happen on aftermarket alarm systems when a remote transmitter (a.k.a. FOB) is lost or broken. Normally before the vehicle is entered the unlock or disarm button on the remote is pressed which unlocks the vehicle's doors while at the same time disengages the system's internal or external anti-theft starter-kill circuit (a.k.a. kill-switch).

This can cause a problem after the remotes are lost or broken if the system was last locked/armed with the remote before the remote was lost or broken and you are now entering the vehicle using a key. Or the vehicle was serviced and the service required disconnecting the vehicle's battery and upon reconnecting the vehicle's battery, the alarm triggered (main reason why to always have a spare remote).

Without a working remote the only way to fix the problem will be to get to the wiring from the system that's stopping power from reaching the vehicle's starter motor. This almost always requires dropping down the vehicle's knee-bolster panel (the panel that's directly across from your knees when your sitting in the driver's seat) and locating the aftermarket system's main control module. 

After the system's main control module is found you will want to look on the module for the brand and model numbers on it. Most system module's will have this information on it, but not all. Knowing the brand and model of system will make it easier to find out what type of anti-theft circuit the system has. If your module doesn't't have any descriptions as to what the brand and/or model it is, not all is lost. There's commonly only 2 types of aftermarket anti-theft circuit designs, internal and external.

If you have a system with an internal (or built-in) starter-defeat circuit (usually found on older systems) you will find 2 wires of the same gauge (size or thickness) and color (one of the two wires may have a color trace or stripe on it). Commonly these wires will be found running into a separate plug on the module or at least side-by-side when found mixed in with other wiring running into the module. But again, they are going to be the same color and gauge no matter how they are found. When you think you found these wires, one way to test to see if you found the correct wires is using an appropriate 12V test probe connected to chassis ground, only one of the two wires will show momentary +12V power only when you try to start the vehicle, the other will show no changes.

After confirmation simple apply a jumper across these two wires so the power from the one wire will reach the other wire during starting of the vehicle. Finally, if the alarm also keeps sounding, just look for some inline fuses on some of the system's wiring and pull them out. Now you can leave the system like this until you get a new remote without having any further starting problems or the alarm triggering.

Now on system's with external starter defeat circuits you will commonly find an external automotive relay with just one wire running from the system to the relay harness. This one wire from the system is the output that is triggering the starter-defeat relay when the alarm is triggered and preventing the vehicle from starting. Commonly found on most systems as a thin gauge Solid ORANGE wire, all that is required is to cut this wire in half then, as with the internal relay types, locate any fuses to the system and pull them out to prevent the system from sounding/triggering.

Posted by: D. Weber AT 11:33 am   |  Permalink   |  0 Comments  |  Email
Tuesday, March 26 2019

Reported Problem: My Remote Car Starter Won't Start!

We get this report almost daily but the main problem is when reported we to be supplied with just a little bit more details. Lets explain; First there's dozens of different situations that can cause a remote starter system to stop functioning properly so the more details you can supply the better so we can pin-point what may be causing the problem and what's not causing the problem.

Details like, what other features does your system have? Does it have keyless entry also? If so, does that feature on the remote work? What about having a 2nd remote, does your 2nd remote get the same response? Did you notice if you get any response from the vehicle when you try to activate the remote starter, like just the parking lights flashing? Or does it turn the ignition on but doesn't crank? Or does crank but doesn't start or starts and then stalls? Or lastly but not final, are you just not getting any response at all from the vehicle when you try to use your remote?...

As you can see this list can go on quite a bit. And sometimes the fix can be as simple as somehow the system was put in valet mode or a worn out button on the remote, or even just the battery in the remote needs replacing. Then sometime's (commonly after after the vehicle was serviced) the system lost it's programming and may need to be taken into a service facility for reprogramming. But regardless of the problem, your probably not going to get to many answers typing in the general term "remote car starter won't start" into Google (unless we pop up!). There's not only 100 different brands and models of remote starters out there, there's even more websites that sell them, and only a handful of those website's can actually supply tech support.

When you do find someone to assist you, have a remote in hand, any information you have on the system that's installed in your vehicle (e.g. brand and model of system) and all the details as to what the system and vehicle is doing or not doing.

Posted by: MCR AT 11:00 am   |  Permalink   |  0 Comments  |  Email
Sunday, March 24 2019

In any situation where the Flashlogic module does not program properly due to a mistake made during the programming procedure or from a faulty or wrong connection or servicing of the vehicle, it is required to reset and reprogram the Flashlogic module to the vehicle using the procedure below:

Step 1: Unplug all harnesses away from the Flashlogic module making sure you unplug the black 4-pin plug last:

Step 2: First, Press & hold in the small black push button on the Flashlogic module, while still holding in the button, plug in just the black 4-pin plug: Response: The LED on the Flashlogic module will begin flashing RED when this is seen release the button:  Response: The LED will turn ON Solid RED for a few seconds then turn OFF, after this is seen, plug in the remaining harnesses to the Flashlogic module:

Step 3: The LED on the Flashlogic module will be steadily flashing GREEN. While the LED is steadily Flashing GREEN, press & hold in the small black push button on the Flashlogic module until the LED lights up Solid GREEN for 1 second and turns OFF, then release the button. The module is now reset and ready for vehicle-specific programming to the vehicle: Repeat the vehicle-specific FLASHLOGIC PROGRAMMING to the vehicle in your manual or CLICK HERE for vehicle-specific module programming.

Posted by: MCR AT 09:26 am   |  Permalink   |  Email
Saturday, March 23 2019

Yes, but to insure safe remote starting of a vehicle with a manual transmission it requires a remote starter system specifically designed to be installed into vehicle's with a manual transmission. These systems install identically to a system for automatic transmissions with the addition of a couple extra outputs & connections (1 connection to the vehicle's parking brake and 1 connection to the vehicle's clutch activation wire) with a manual transmission compatibility setting. Known as a "Remote Start Ready Mode", this feature requires the driver to enable the vehicle to be remote started after the vehicle is parked; you can't just randomly remote start the vehicle anytime you want like you can with a remote starter on a automatic trans vehicle, you have to prepare the vehicle to be remote started...

While the vehicle is still running with the keys, the driver places the vehicle in neutral, set's the parking brake and then press and holds in the button on the remote until the dash lights flash (activation procedures will vary). Then the driver turns off the ignition, removes the keys, and exits the vehicle. When the remote start ready mode is set correctly, the vehicle will remain running while exiting the vehicle. Once the driver's door is closed the driver presses the button on the remote 1X which will lock the vehicle's doors (if equipped with factory power door locks, otherwise it will just shut down the vehicle) and it will automatically shut down the engine. The vehicle is now ready to be safely remote started.

In the event that the driver re-enters the vehicle without activating the remote starter, opening the driver's door will cancel out the remote start ready mode and the driver would have to perform the remote start ready mode procedure again.

Posted by: MCR AT 04:45 pm   |  Permalink   |  0 Comments  |  Email
Friday, March 22 2019

You may not see the need to go beyond your garage or driveway to remote start your car, but increased range with 2-way confirmation is definitely an advantage when your parked at work, out shopping or in a restaurant, especially when the weather is bad.

With standard remotes, you're looking out the window to see if your parking lights are on (or you can see the exhaust when it's cold) or the horn to beep to confirm that you successfully activated the remote starter. With a 2-way remote, the advantage is when your vehicle is out of sight you can be sitting at your table in a restaurant or in the checkout line at the grocery store and have visual LCD screen or LED's and sound confirmation right on your remote that your vehicle has remote started, or not! Even double check that you locked the vehicle's doors and more!

Posted by: MCR AT 05:50 pm   |  Permalink   |  0 Comments  |  Email
Thursday, March 21 2019

Reported Problem: New Prestige Z Series Install. Negative parking brake input connection good. Turbo-timer turned ON and set for 3 minutes in programming but the turbo cool-down mode will not activate.

Possible Fix: This feature must be activated after installation is completed. This is only required the first time the turbo timer is needed. After activation the system will always automatically enter turbo timer mode when the parking brake is activated: With the vehicles engine running for more than 15 seconds: Activate Parking Brake: Press the programming button on the antenna 2X: The parking lights will flash 2X to indicate turbo timer mode has been activated.

Posted by: MCR AT 09:00 am   |  Permalink   |  0 Comments  |  Email
Wednesday, March 20 2019

#1 Most Common Remote Starter Installation Problem

After 30 years of being under a dash installing everything from old-school kill-switches, anti-theft coded key-pads, auto alarms and later remote starter systems, there's not many problems that I haven't seen, heard of, read about in manufacturer's technical bulletins or actually caused myself, that installers I've provided tech support to over the last 17 years that have reported a new installation problem to me;

So, that being said, in my experience, I have to say that the #1 problem that I have found to be the cause of a "oddly-working", "barely working" or "blame it on the system, not the installer" problem is due to a faulty or bad chassis ground to the system...

It's not as easy to find and confirm a good negative -12V chassis ground source in a vehicle as it is to locate a positive +12V source. Simply put, most ground sources in a vehicle fluctuate (and I'm confident that most professional automotive audio installers can testify to this statement). This is why you can't tap into any existing factory ground wires in the vehicle, dash support brackets or most steering column supports either.

Without indepth explanation (I've learned it's not so much what's causing the problem, it's "how to fix it"!) alway's use a self-tapping screw through any metal that is painted the same color as the exterior of the vehicle. Example places I personally place my grounds; behind the left kick-panel or on the firewall. And don't over tighten and strip the self-tapping screw!

Posted by: D. Weber AT 09:00 am   |  Permalink   |  0 Comments  |  Email
Tuesday, March 19 2019

Reported Issue: New install. Ignition turns ON, no crank at all then the ignition turns off and the system automatically tries 3 more times but still no crank.

Possible Causes:
#1: One of the systems constant input power wires (which is the feed output for the system's crank/start output wire) is not receiving constant power.
#2: Wrong or bad connection from the system to vehicle's starter wire (this would be the wire in the vehicle's ignition harness that only shows +12 Volts only when the vehicle is being cranked/started with the key).
#3: Vehicle's bypass interface kit needed or not properly programmed.

Posted by: MCR AT 08:00 pm   |  Permalink   |  0 Comments  |  Email
Monday, March 18 2019

Reported Issue: LED on Flashlogic Module will not light up as indicated during programming after ignition is turned ON

Possible Fix: This is good indication that the Flashlogic module's ignition input wire (Solid PINK wire) is not receiving power when the ignition is turned on. Check the connection.

Posted by: MCR AT 12:38 pm   |  Permalink   |  0 Comments  |  Email
Monday, March 11 2019

1. Turn the vehicle’s ignition to the full ON position (the last position the ignition can be in before actually starting the vehicle. Do not start the vehicle) within 10 seconds:

2. Press and hold in the system’s programming button that’s built into the system’s antenna (commonly mounted on the inside top center of windshield) until the system sounds 3X then release the button, on remote starter only systems, just the dash lights will flash 3X, then within 10 seconds:

3. Press and hold the LOCK button on the transmitter (or CIRCLE ARROW button on 1 button remotes): the system will sound 1X (or dash lights will flash 1X on remote starter only systems) within 3 seconds indicating the transmitter has been programmed:

4. Repeat just step 3 on any additional transmitters at this time, up to a total of 4 transmitters can be programmed at a time. Turn the ignition off, remove keys and test remote.

Do not allow more than 10 seconds to lapse between steps or the program mode will automatically turn off and you will have to start over.

Posted by: NCR AT 04:07 pm   |  Permalink   |  Email
Sunday, March 10 2019

Reported Issue: Remote Starter tries to Start 3 times then Stops (Ignition turns ON, no crank)

Application: During new install testing or existing system that worked fine prior to current problem

Possible Cause(s): Several situations can cause this problem: #1: May need additional bypass kit to complete installation or bypass kit not programmed properly (new install) or system lost bypass kit programming (pre-working system). #2: Using tachless-mode and the tachless mode is not picking up enough voltage level (new install). #3: Wrong or bad connection to vehicles' starter wire or one of the two constant power wires to the remote starter system that relays' momentary power to the starters crank output wire is not getting constant power (bad or wrong connection).

Posted by: D. Weber AT 09:00 am   |  Permalink   |  0 Comments  |  Email
Saturday, March 09 2019

How to Program Prestige Remote Starter Remote:

Step 1: Turn Ignition ON (DO NOT start the vehicle): Press & release the button on the system's antenna 3X (system antenna is commonly found mounted on the inside top center on the windshield behind the rearview mirror or in the upper left corner of windshield): Dash lights and horn will beep 1X in response (if system has horn output feature):

Step 2:  Press & release the LOCK button on the remote (or the 1 button on 1 button remotes) 1X: the dash lights and horn will beep 1X in response indicating that the remote has been programmed to the system:

Step 3: Press & release the LOCK button on any additional remote(s) (or the 1 button on 1 button remotes) 1X: the dash lights and horn will beep 1X in response indicating that this remote has also been programmed to the system:

Step 4: After all remotes have been programmed to the system, turn the ignition OFF, wait, the system will sound within 5 secs. Done. Test remote(s).

Posted by: MCR AT 12:09 pm   |  Permalink   |  0 Comments  |  Email
Friday, March 08 2019

Step 1: Turn Ignition ON (DO NOT start the vehicle): Press & release the button on the system's antenna 3X: Dash lights and horn will beep 1X in response (if system has horn output feature):

Step 2: Turn ignition OFF & ON again: system will flash the dash lights and beep the horn 2X:

Step 3: Turn ignition OFF & ON again: system will flash the dash lights and beep the horn 3X:

Step 4: Press & release the button on the system's antenna 3X slowly: LED on antenna will flash in a 3 flash/pause/3 flash pattern in response:

Step 5: Press & release the LOCK button on the remote (or the 1 button on 1 button remotes): the dash lights and horn will beep in response. The number of flashes/beep per-press of the remote's button will indicate the current run time setting:

Step 6: Just keep press & releasing the remotes button until the number of flashes/beeps corresponds with the run time setting you desire:  1 = 5 Mins.  2 = 10 Mins.  3 = 15 Mins.  4 = 20 Mins.  5 = 45 Mins.  6 = 60 Mins.

Step 7: After the desired setting is chosen turn the ignition OFF, wait, the system will sound within 5 secs. Done.

Posted by: MCR AT 12:00 pm   |  Permalink   |  0 Comments  |  Email
Thursday, March 07 2019

Reported Issue: Remote FOB works intermittently

Situation: Remote locks doors fine but have to press unlock several times to get it to unlock the vehicle, same with the remote start button

Possible Cause: Beside's at least trying a fresh battery in the remote, the remote definitely sounds like it's just wearing out and you need a new replacement. Could try taking the remote apart and spraying a little electronic circuit cleaner over the push buttons on the PC board might help if its due to dirty pots.

Possible Fix: Purchase and program a new remote.

Posted by: MCR AT 09:21 am   |  Permalink   |  0 Comments  |  Email
Wednesday, March 06 2019

Reported Issue: Bought used car with a Code Alarm system installed (can also apply to most other brands of systems).

Situation: Remotes lock and unlock vehicle but no crank or power to starter motor. Replaced battery in vehicle.

Possible Cause: Internal or external starter defeat relay stuck open (very, very rare possibility, especially on system's with external starter defeat relay).

Possible Fix: On system's with external relay: Press unlock (or disarm) on remote: Hold relay in hand and turn ignition ON, if you feel the relay click then it's a bad output from the system: Commonly you'll find a Solid ORANGE wire connected to the relay. Cut this orange wire in half to permanently disable the starter defeat relay.

If the relay doesn't click, this is normal operation and indicates that the system may not be causing the no start problem. To double check that the relay is working properly, close all the vehicle's doors, press lock (arm) on the remote. Wait at least 30 seconds and again holding the relay in hand, turn the ignition on, the relay will click ON. Then turn ignition off and press unlock (disarm) on remote. The relay will click once more (OFF).

Systems with internal starter defeat relay: In general, most systems will have 2 wires that are the same color and gauge, and the wires will be running into the same plug commonly right next to each other. One of the wire's may have a color stripe on them. On most Code Alarm system's for example, these 2 wires will be 2 purple wires (1 with a red stripe) or 2 white wires (1 with a red stripe) or 2 yellow wires (1 with a red stripe). You will have to place a jumper wire across these two wires to connect them together. You cannot just disconnect the module! If it's the system causing the no start problem then the vehicle will start right up after jumping the wires together.

When the above procedures have been applied to your specific system and the vehicle will still not crank, it's definitely a mechanical or electrical problem with the vehicle and not the system causing the problem.

Posted by: MCR AT 05:35 pm   |  Permalink   |  0 Comments  |  Email
Wednesday, March 06 2019

Reported Issue: Remote starter system worked fine until vehicle was serviced. Keyless entry works fine but when the remote starter is activated it only flashes the parking lights 7X

Situation: Existing system or during new system installation test

Specific Vehicle, System or Bypass Interface: Applies to Code Alarm, Prestige and Pursuit Brand Remote Starter systems.

Possible Cause: System lost tachometer signal/not detected: When either a Code Alarm or Prestige remote starter system flashes the vehicle's parking lights 7 times after activating the remote start feature, either during installation testing or after the system was installed and remote started perfectly, this is indication that the tachometer signal from the vehicle wasn't programmed or programmed properly to the system (new install) or somehow (usually from the vehicle being serviced) the system lost it's programming due to the vehicle's battery being disconnected or electrical service problems etc.

Possible Fix: Reprogram tachometer signal to system

Tachometer Programming: (Each step must be done within 5 seconds of the next step) Step 1: Turn ignition on (do not start the vehicle) S2: Press & release the button on the systems antenna 3X. S3: Turn ignition OFF. S4: Press & hold the button on the antenna. S5: While still holding the button in, start the vehicle. Keep holding the button in until either the dash lights flash 4X or the system beeps/chirps 4X. S6: Release button: Dash lights will turn on solid for 3 seconds and shut off. Turn ignition OFF, remove keys and test remote start.

Posted by: MotorCityRemotes AT 05:47 am   |  Permalink   |  Email
Monday, March 04 2019

Reported Issue: Remote starter system worked fine until vehicle was serviced. Keyless entry works fine but when the remote starter is activated it will only turn the ignition ON, no crank

Situation: Pre-Equipped/Installed

Specific Vehicle, System or Bypass Interface: 2012 Ford F150 w/Code Alarm System & Flashlogic FLTB1

Possible Cause: Flashlogic FLTB1 lost programming

Possible Fix: Reset & reprogram module to vehicle (2 keys to vehicle required for programming): Unplug both plugs from Flashlogic module: Press & hold in the small black push button on the Flashlogic module, while still holding the button in, plug just the black 4-pin plug in, wait, the LED on the Flashlogic module will begin the flash rapidly, when this is seen release the button. Plug in the remaining harness. The LED will be slowly flashing green, while this is seen press & hold in the button again until the LED turns on solid green then turns off, after this is seen release the button. The Flashlogic module is now reset and ready to be reprogrammed to the vehicle:

Module Programming: MUST have 2 OEM keys to the vehicle to program (cannot use a cloned key): Turn ignition ON with the first key (DO NOT start the vehicle): The LED on the Flashlogic module will turn on solid RED then turn OFF: Within 5 seconds turn ignition OFF remove key and turn ignition ON with 2nd key, LED will again turn ON Solid RED then turn OFF, within 5 seconds remove key and press & release the button on the Flashlogic module: within another 5 seconds activate the remote starter: wait, the LED will turn Solid RED to GREEN: Module reprogrammed to vehicle: press and release the vehicle's brake pedal and test remote start.

Posted by: MotorCityRemotes AT 02:40 pm   |  Permalink   |  0 Comments  |  Email
Monday, March 04 2019

Reported Issue: Installed DLRKP module to 1998 F150 without RKE (5-Wire). Fuse blows when testing remote lock/unlock.

Situation: New Install

Specific Vehicle, System or Bypass Interface:  Voxx DLRKP 5-Wire Door Locks Relay Module on 1998 Ford F150

Possible Cause: Lock and/or unlock outputs from DLRKP to vehicle are connected in wrong directions

Possible Fix: When the 20A fuse blows on the DLRKP module when pressing either lock or unlock on one of the systems remotes when first testing the installation, this is indication that whichever function (lock or unlock) that the fuse blew on, the corresponding lock or unlock wire that was cut in half in the vehicle, the wires from the DLRKP module were connected to them in the wrong directions.

Posted by: Jake AT 07:25 am   |  Permalink   |  Email
Sunday, March 03 2019

Reported Issue: System works fine with factory remote but doesn't't work consistently (or at all) after remote upgrade. Have to press the button on the remote several times to work.

Situation: Adding long range remote upgrade

Specific Vehicle, System or Bypass Interface:  Plug&Play w/OBDII T-harness or Standalone Module's w/ADS Protocol

Possible Cause: Insufficient low constant power and/or ground to system antenna from OBDII connector

Possible Fix: Run separate constant power and ground connections directly to remote upgrade antenna. Cut separate constant power and ground wires running from T-harness to antenna plug and cover the ends of the wires that are running into the OBDII side of the harness with electrical tape or crimp cap off. Connect ground wire running into antenna directly to chassis ground and then connect the constant power wire running into the antenna to a constant power wire in the vehicle, preferably a constant power wire found in the vehicle's ignition harness.

Posted by: Jake AT 06:32 am   |  Permalink   |  Email
Friday, March 01 2019

Reported Issue: Remote starts fine but only runs for only approx. 10 seconds then shuts down:

Situation: New Install w/o Tachometer Connection

Specific Vehicle, System, or Bypass Interface: General troubleshooting

Possible Cause: System programmed for "Voltage Detection" Setting with Voltage detection level set to high:

Possible Fix: Program system for less than 1/2 Volt detection (<0.5)

Reason for the adjustment: The system is not detecting the vehicle's alternator kicking in after remote start/crank. The system needs to detect at least 1/2 a volt raise in the voltage levels on the interior side of the vehicle's wiring; the wires to the remote starter wires are directly connected. After start, the system waits to detect the voltage to raise and if no raise over 0.5V is detected within a short time the system will shut down assuming the vehicle did not start or stalled (many system models will automatically try to restart the vehicle again on its own).

Recommended Fix: Hard-wire the system's tachometer input wire to the vehicle's tachometer wire and program tach signal to the system. Using any system's tachometer input option is the best way to go 98% of the time.


Posted by: D.Weber AT 11:00 am   |  Permalink   |  Email

PAGE VISITS SINCE 03-01-2019: - -


Sales/Assistance/Product Questions:
Toll-Free: 1-866-244-8004
Tech-Direct Line: 1-586-315-4005

Mon-Fri: 8am-7pm, Sat: 9am-5pm & Sun: 9am-3pm ET
CLOSED: Holidays & Holiday Weekends

Located in New Baltimore Michigan
Online Since 2002

Website, Sales & Support Office:
50935 Washington St. Ste 2, New Baltimore MI. 48047
TECHNICAL SUPPORT: 1-586-315-4005

Last Website Update: 05-19-2022 11:45 AM ET