The VSS Advantage:
Step-by-Step, System-to-Vehicle Specific Installation Guide:
Information is Everything! No sitting with a lap-full of "spaghetti-wire" and jumping from wiring chart to manual, trying to figure out what wires are needed (or not needed) to connect to the vehicle. Each of our system's include a step-by-step, vehicle-specific installation manual that indicates exactly what wire from the system connects to what wire in the vehicle, where the wire is located in the vehicle, and how to confirm that you found the correct wire using the VSS kits supplied LED style test probe.
LED Style Test Probe Included:
No need for using awkward multi-meters that indicate voltage level's that can confuse polarity readings and require the use of two probes and a bare spot on the wire in order to take a reading. Each of our VSS kits includes an easy-to-use LED style test probe to use along with the VSS kits' step-by-step vehicle-specific installation manual. This test probe simplifies the procedure of finding and testing for the correct wire in your vehicle by lighting a green or red LED to indicate the target wire's polarity (explained in each step of our vehicle-specific install manuals).
For example, if the step in the VSS guide indicates that the vehicle's parking light wire is a solid blue wire found running into the rear of the vehicle's headlights switch and will show a positive polarity when the parking lights switch is turned on, you simply connect the probes alligator clip to chassis ground, stick the tip of the probe thru the wire's insulation and turn the vehicle's parking light's ON & OFF a few times, and if its the correct blue wire, it will light the red LED in the handle of the test probe at the same time the switch is turned ON & OFF! (again, explained in each step of the VSS manual). It just can't be made any simpler than this!
Includes Vehicle Specific NKR ("No Key Required") Bypass Interface Kit:
No need to give up one of your vehicle's keys (or purchase a 3rd key) in order to install a remote car starter in your vehicle like with most other remote starter kits. The NKR bypass kit included with a VSS system only requires your vehicle's keys for programming, not operation, meaning you don't have to stick one of your keys in a box!
The majority of vehicles on the road today have some type of anti-theft system installed on them from the factory, this can range from the transponder key type typically found in (but not limited to) most Ford, Chrysler/Dodge, Honda, and Toyota vehicles to one of several versions of a Passlock system found in most vehicles manufactured by General Motors. When a vehicle is equipped with a factory anti-theft ignition system, an additional bypass interface kit is necessary to install any brand of remote starter system. After ordering, our technicians will know what is required for your specific vehicle's installation and include it in with the system.
Data Bypass/Interface Port:
Dedicated input used when installing the additional bypass interface kit required for most vehicles on the road today equipped with factory-installed anti-theft systems. This plug-in port eliminates any wiring needed between the remote starter module and the bypass kit (bypass/interface kit included. Wiring between the bypass interface and vehicle required).
Designed to eliminate the need to run a wire out under the hood to connect to the vehicle's tachometer wire and then having to program the tach signal to the remote starter system: The tachless mode monitors the vehicle's voltage levels, current and crank time during start to maintain a trouble-free remote starter activation. Applicable to newer and well-maintained vehicles with gas or hybrid engines only.
Includes Vehicle Specific Extras:
To avoid the inconvenience of getting into the middle of an installation and finding out that you need to stop and run to the auto parts store for a relay or radio shack for some resistor's or whatever, we include any needed extra relays w/harness (for example, for power trunk activation, 3rd Accessory, etc.) and/or diodes, resistors, voltage inverters, etc. needed for your specific vehicle.
Installation Connector Package:
Each VSS system includes 3 different sizes of quick-connect "T-Tap" connectors with male spade connectors pre-crimped to the ends of the wiring of the system for making quick connections from the system to your vehicle's wiring. Also included are crimp cap connectors for connecting wires end-to-end and self-tapping screws with ground loop connectors for making chassis ground connections to the vehicle. Nylon zip ties are also supplied for securing wiring, control module, and sensor placement.
Vehicle Compatibility Guarantee:
You will be asked to indicate the year, make and model of vehicle the system will be installed into during ordering. If in the rare event that one of our technicians finds that the system is not compatible with your specific vehicle, we will immediately contact you, void the order and promptly release your payment.
Lifetime Technical Support:
Have access to some of the most qualified technicians in the industry, 7 days a week. Providing technical support since 2002, each member of our technical support staff has a minimum of 10 years of hands-on experience installing alarms, keyless entry, and remote car starter systems. And with one of the largest support networks in the industry, our technicians can be directly contacted via Phone, email, through our Troubleshooting BLOG, LIVE CHAT, and even by text. With our wide range of communication options, if you ever have a problem or question you can feel confident that you can easily contact someone in our technical support department.