2018 & 2019 Ford F-150 DIY Remote Start Installation

for Ford F-150 with Push-to-Start Ignitions

Ford Vehicle-Specific Ready Remote Start Systems

► Activated by Pressing your Ford Keyless Entry Remote's Lock Button 3 Times

 ► 1-Plug to Vehicle Installation  ► No Tools Required   ► No Hard-Wiring

► No Additional Parts Required   ► No Key or Dealer Programming Required

► 2-Year Warranty  ► 45-Day Money-Back Performance Guarantee

► Viper™ Long-Range Remotes Upgradable
 

Go Straight from Delivery to Installation!

For 2018 & 2019 Ford F-150s with Key Ignitions: 

► 2018 & 2019 Ford F-150 Remote Start Installation Details:

• 1-Plug to Vehicle Installation: No wire cutting or splicing. No tools or dash panel removal required. Just 1 T-harness connection to the rear of your vehicle's OBD2 port is all that's required to install this system into a 2018 & 2019 Ford F-150 with Ford smart keys, push-to-start ignitions (see example photos below.)
   
• No key programming procedures, no additional parts, no computers, or special dealer programming involved.
   
• Easy Step-by-Step Illustrated Installation Guide
   
• YouTube Installation Demo Videos
   
• Average Installation Time: <30 Minutes.

► Easy, 5-Step, Remote Start Plug-In Installation:

Step 1: Unplug your vehicle's gateway connector found right behind your vehicle's OBD2 diagnostic plug on the lower left side of the driver's side dash (see photos below) and plug it into the female plug on the T-harness, and then replace the gateway plug with the gateway plug from the T-harness...

Step 2: Next, plug the blue plug from the T-harness into the blue plug on the remote starter module...in response, the RED LED on the module will light up, indicating that it's receiving power...

Step 3: Now you need to turn on the system: With your eyes on the red LED, turn the ignition ON (don't start the vehicle); in response, the RED LED will turn to Solid Green and then turn off; after you see this, turn the ignition OFF; exit the vehicle, close all the vehicle's doors, and lock the doors with the vehicle's remote...

Step 4: Time to test remote start activation: Slowly press LOCK 3 times on your keyless entry remote: After the vehicle remote starts, let it test run for at least a minute. Now, unlock the vehicle with your remote, enter the vehicle, and press & release the vehicle's brake pedal. In response, the engine will shut down.

Step 5: Lastly, secure the remote start module and harness up under the driver's dash using the supplied zip ties. DONE!
 

► 2018 & 2019 Ford F-150 Remote Start Installation Details:

• 1-Plug to Vehicle Installation: No wire cutting or splicing. No tools or dash panel removal required. Just 1 T-harness connection to the rear of your vehicle's OBD2 port is all that's required to install this system into a 2018 & 2019 Ford F-150 with Ford smart keys, push-to-start ignitions (see example photos below.)
   
• No key programming procedures, no additional parts, no computers, or special dealer programming involved.
   
• Easy Step-by-Step Illustrated Installation Guide
   
• YouTube Installation Demo Videos
   
• Average Installation Time: <30 Minutes.

► Easy, 5-Step, Remote Start Plug-In Installation:

Step 1: Unplug your vehicle's gateway connector found right behind your vehicle's OBD2 diagnostic plug on the lower left side of the driver's side dash (see photos below) and plug it into the female plug on the T-harness, and then replace the gateway plug with the gateway plug from the T-harness...

Step 2: Next, plug the blue plug from the T-harness into the blue plug on the remote starter module...in response, the RED LED on the module will light up, indicating that it's receiving power...

Step 3: Now you need to turn on the system: With your eyes on the red LED, turn the ignition ON (don't start the vehicle); in response, the RED LED will turn to Solid Green and then turn off; after you see this, turn the ignition OFF; exit the vehicle, close all the vehicle's doors, and lock the doors with the vehicle's remote...

Step 4: Time to test remote start activation: Slowly press LOCK 3 times on your keyless entry remote: After the vehicle remote starts, let it test run for at least a minute. Now, unlock the vehicle with your remote, enter the vehicle, and press & release the vehicle's brake pedal. In response, the engine will shut down.

Step 5: Lastly, secure the remote start module and harness up under the driver's dash using the supplied zip ties. DONE!
 

► 2018 & 2019 Ford F-150 Remote Start Installation Details:

• 1-Plug to Vehicle Installation: No wire cutting or splicing. No tools or dash panel removal required. Just 1 T-harness connection to the rear of your vehicle's OBD2 port is all that's required to install this system into a 2018 & 2019 Ford F-150 with Ford smart keys, push-to-start ignitions (see example photos below.)
   
• No key programming procedures, no additional parts, no computers, or special dealer programming involved.
   
• Easy Step-by-Step Illustrated Installation Guide
   
• YouTube Installation Demo Videos
   
• Average Installation Time: <30 Minutes.

► Easy, 5-Step, Remote Start Plug-In Installation:

Step 1: Unplug your vehicle's gateway connector found right behind your vehicle's OBD2 diagnostic plug on the lower left side of the driver's side dash (see photos below) and plug it into the female plug on the T-harness, and then replace the gateway plug with the gateway plug from the T-harness...

Step 2: Next, plug the blue plug from the T-harness into the blue plug on the remote starter module...in response, the RED LED on the module will light up, indicating that it's receiving power...

Step 3: Now you need to turn on the system: With your eyes on the red LED, turn the ignition ON (don't start the vehicle); in response, the RED LED will turn to Solid Green and then turn off; after you see this, turn the ignition OFF; exit the vehicle, close all the vehicle's doors, and lock the doors with the vehicle's remote...

Step 4: Time to test remote start activation: Slowly press LOCK 3 times on your keyless entry remote: After the vehicle remote starts, let it test run for at least a minute. Now, unlock the vehicle with your remote, enter the vehicle, and press & release the vehicle's brake pedal. In response, the engine will shut down.

Step 5: Lastly, secure the remote start module and harness up under the driver's dash using the supplied zip ties. DONE!